SIMCO Electronics
SIMCO Electronics | Radio Frequency Technician | phoenix, az
SIMCO Electronics, Phoenix, Arizona, United States,
Position Overview
The Radio Frequency Calibration Technician will apply knowledge of measurement science, mathematics, physics, and electronics to calibrate inspection, measurement, and test equipment in the Acoustical, Chemical, Dimensional, DC/Low Frequency, RF/Microwave, Fluid, Mechanical, Optical, Thermodynamics, and Time & Frequency disciplines to ensure measurement accuracy. The Radio Frequency Technician will identify and utilize appropriate manual and automated measurement procedures.
This position will normally receive no instruction on work, applying job skills and company policies and procedures to complete a wide range of difficult tasks, and working on assignments that are moderately complex in nature where judgment is required in resolving problems and making routine recommendations. The Radio Frequency Calibration Technician will perform laboratory housekeeping and may perform some administrative duties. The Radio Frequency Technician may be asked to report opinions and interpretations.
Responsibilities and Duties Calibrate inspection, measurement, and test equipment (IM&TE) in one or more of the following disciplines – Acoustical, Chemical, Dimensional, DC/Low Frequency, RF/Microwave, Fluid, Mechanical, Optical, Thermodynamics, and Time & Frequency, in order to ensure compliance with published specifications Working with a range of RF-enabled devices including cell phone antennas, amplifiers, two-way radios, satellite systems, and internet access points. Troubleshooting circuits used in RF transmission independently and with site engineers. Identifying and repairing faults in finished assemblies making adjustments as required. Identifying the causes of faults and work with on-site teams to implement preventative measures so that they do not happen again. Model creation, assembly, tuning, and plan development as well as modifying antenna prototypes, parts, and assemblies. Maintaining documentation of test cases. Performing routine antenna capability tests. Maintain primary and/or intrinsic calibration standards Maintain secondary and/or working calibration standards Perform maintenance, troubleshooting and repair of precision equipment Develop calibration procedures and methods, according to detailed specifications, blueprints, drawings, and other technical requirements Collect, compile, measure, summarize, and record data gathered during calibration. Identify IM&TE out-of-tolerance conditions and perform corrective action via adjustments, component replacement, correction factors, etc Identify and correct measurement errors, as applicable Prepare calibration reports and certificates Adapt existing calibration equipment, standards, and techniques to accomplish unique measurements tasks for which they are not principally used Perform uncertainty evaluation and analysis for measurement standards and associated measurement processes Train subordinates in calibration concepts and procedures Interact with other technicians, Customer Service Representatives, Account Managers, and customers Other duties and responsibilities as may be assigned
Qualifications Minimum High School diploma or equivalent Must be able to perform general math and algebra functions Understanding of Basic Statistics Must possess good written and oral, communication skills Technical writing ability Intermediate ability to troubleshoot repair, align and optimize precision equipment Intermediate computer skills Proficient in use of MS Word and Excel Minimum three years of calibration experience some of which can be offset with formal metrology training Knowledge of Quality Management system (ISO 9001, ISO 17025 and ANSI Z540) Must have great interpersonal and customer service skills Strong attention to details Must be a self-motivator, work as a team player, and follow written procedures
Physical Demands Must be able to lift up to 45 pounds without assistance Occasional standing and bending are required
Working Environment Works primarily in a laboratory or manufacturing environment at a SIMCO location and/or customer sites Travel may be required to other domestic and possibly international locations
What We Offer Full - Time, non-exempt position Excellent benefits package includes; medical, dental, vision, disability, life insurance, 401(k) with company matching, employee funded pre-tax health, child care spending accounts and tuition reimbursement Vacation, sick and paid holidays
SIMCO provides equal employment opportunities (EEO) to all employees and applicants for employment without regard to race, color, religion, sex, national origin, age, disability or genetics. In addition to federal law requirements, SIMCO complies with applicable state and local laws governing nondiscrimination in employment in every location in which the company has facilities. This policy applies to all terms and conditions of employment, including recruiting, hiring, placement, promotion, termination, layoff, recall, and transfer, leaves of absence, compensation and training.
The Radio Frequency Calibration Technician will apply knowledge of measurement science, mathematics, physics, and electronics to calibrate inspection, measurement, and test equipment in the Acoustical, Chemical, Dimensional, DC/Low Frequency, RF/Microwave, Fluid, Mechanical, Optical, Thermodynamics, and Time & Frequency disciplines to ensure measurement accuracy. The Radio Frequency Technician will identify and utilize appropriate manual and automated measurement procedures.
This position will normally receive no instruction on work, applying job skills and company policies and procedures to complete a wide range of difficult tasks, and working on assignments that are moderately complex in nature where judgment is required in resolving problems and making routine recommendations. The Radio Frequency Calibration Technician will perform laboratory housekeeping and may perform some administrative duties. The Radio Frequency Technician may be asked to report opinions and interpretations.
Responsibilities and Duties Calibrate inspection, measurement, and test equipment (IM&TE) in one or more of the following disciplines – Acoustical, Chemical, Dimensional, DC/Low Frequency, RF/Microwave, Fluid, Mechanical, Optical, Thermodynamics, and Time & Frequency, in order to ensure compliance with published specifications Working with a range of RF-enabled devices including cell phone antennas, amplifiers, two-way radios, satellite systems, and internet access points. Troubleshooting circuits used in RF transmission independently and with site engineers. Identifying and repairing faults in finished assemblies making adjustments as required. Identifying the causes of faults and work with on-site teams to implement preventative measures so that they do not happen again. Model creation, assembly, tuning, and plan development as well as modifying antenna prototypes, parts, and assemblies. Maintaining documentation of test cases. Performing routine antenna capability tests. Maintain primary and/or intrinsic calibration standards Maintain secondary and/or working calibration standards Perform maintenance, troubleshooting and repair of precision equipment Develop calibration procedures and methods, according to detailed specifications, blueprints, drawings, and other technical requirements Collect, compile, measure, summarize, and record data gathered during calibration. Identify IM&TE out-of-tolerance conditions and perform corrective action via adjustments, component replacement, correction factors, etc Identify and correct measurement errors, as applicable Prepare calibration reports and certificates Adapt existing calibration equipment, standards, and techniques to accomplish unique measurements tasks for which they are not principally used Perform uncertainty evaluation and analysis for measurement standards and associated measurement processes Train subordinates in calibration concepts and procedures Interact with other technicians, Customer Service Representatives, Account Managers, and customers Other duties and responsibilities as may be assigned
Qualifications Minimum High School diploma or equivalent Must be able to perform general math and algebra functions Understanding of Basic Statistics Must possess good written and oral, communication skills Technical writing ability Intermediate ability to troubleshoot repair, align and optimize precision equipment Intermediate computer skills Proficient in use of MS Word and Excel Minimum three years of calibration experience some of which can be offset with formal metrology training Knowledge of Quality Management system (ISO 9001, ISO 17025 and ANSI Z540) Must have great interpersonal and customer service skills Strong attention to details Must be a self-motivator, work as a team player, and follow written procedures
Physical Demands Must be able to lift up to 45 pounds without assistance Occasional standing and bending are required
Working Environment Works primarily in a laboratory or manufacturing environment at a SIMCO location and/or customer sites Travel may be required to other domestic and possibly international locations
What We Offer Full - Time, non-exempt position Excellent benefits package includes; medical, dental, vision, disability, life insurance, 401(k) with company matching, employee funded pre-tax health, child care spending accounts and tuition reimbursement Vacation, sick and paid holidays
SIMCO provides equal employment opportunities (EEO) to all employees and applicants for employment without regard to race, color, religion, sex, national origin, age, disability or genetics. In addition to federal law requirements, SIMCO complies with applicable state and local laws governing nondiscrimination in employment in every location in which the company has facilities. This policy applies to all terms and conditions of employment, including recruiting, hiring, placement, promotion, termination, layoff, recall, and transfer, leaves of absence, compensation and training.